Unmodified thin-set is Portland cement, sand and water retention agents, covered by ANSI A118.1; modified mortars add polymers and are covered by A118.4, A118.11 and A118.15.1 A118.15 uses the same tests as A118.4 with stricter requirements.2 Letters after the number mark extra properties: E for extended open time, T for sag resistance, H for large and heavy tile, F for fast set.2
Thin-set mortar is the least glamorous item on a tile submittal and one of the most consequential. It carries the bond, and the standard printed on the bag is what a specification, a membrane maker and a tile maker all rely on. The naming looks cryptic from the outside. It is actually a short, readable code.
Unmodified and modified
Schluter, a membrane manufacturer, gives the plain definitions. Unmodified thin-set mortar is a blend of Portland cement, sand and water retention agents, mixed with water by the user. Its product standard is ANSI A118.1, and it may also be called dry-set mortar.1 Modified thin-set mortars are similar but include additional polymers such as latex. They are added either as a liquid the user mixes in place of water, or as powder already in the bag.1 The standards for modified mortars are ANSI A118.4, ANSI A118.11 and ANSI A118.15.1
TEC describes the categories the same way, listing dry-set (unmodified), polymer-modified, and epoxy mortars and grouts.2 It notes polymer-modified mortars have better performance and handling than dry-set mortars.2

A118.4 and A118.15
Two modified standards appear on most bags, and the difference is strictness, not chemistry. TEC explains that A118.4 is the specification for modified dry-set cement mortar, and A118.15 is the specification for improved modified dry-set cement mortar.2 A118.15 uses the same tests as A118.4 but has stricter requirements, and TEC describes A118.15 mortars as the best performing available today.2 A third standard, A118.11, is specific to bonding over exterior glue plywood, and TEC notes that most A118.15 mortars meet or exceed it.2
The letters after the number
ANSI adds letters where a mortar meets further requirements. TEC lists them: E for extended open time, T for sag resistance on vertical surfaces, H for large and heavy tile, and F for fast set.2 The letters follow the specification number, so a bag marked A118.4HTE meets the modified standard plus the large-and-heavy, sag-resistance and extended-open-time requirements.2
Those designations map onto real site problems. Extended open time helps when a crew is setting large pieces slowly, and sag resistance keeps tile from slumping on a wall. The large-and-heavy designation matters for the oversized porcelain behind most lippage disputes. See tile lippage control.

When the membrane chooses the mortar
Here is where contractors most often get caught. An uncoupling or waterproofing membrane may require a specific mortar type above or below it, and that requirement overrides the general rule that stronger is better. Schluter publishes guidance on identifying modified and unmodified mortar precisely because its membranes specify which to use.1 The TCNA Handbook's membrane section covers bonded sheet membranes, liquid-applied crack isolation and waterproofing membranes, and uncoupling membranes, each with its own service rating.3 Read the membrane's instructions before buying mortar, and submit the combination together.
Coverage matters as much as the mortar
A premium mortar laid badly still fails. The TCNA Handbook sets average mortar contact coverage at 80% in dry areas and 95% in wet areas, evenly distributed to support edges and corners.3 It makes a point that catches people out. Coating the back of the tile does not by itself constitute coverage, which is where mortar contacts both the tile and the substrate.3 Donato Pompo, writing in The Construction Specifier, traces excessive lippage to a combination of poorly prepared substrates, improper installation methods, improper use of materials and poor workmanship.4
High-performance mortars and where they earn their cost
TEC names the cases where a high-performance mortar matters: exteriors, facades, submerged installations and gauged porcelain panels.2 It lists the benefits as extra bond strength, long open time, freeze-thaw stability and water immersion performance, and notes these mortars typically carry a longer limited product warranty.2 On an interior commercial floor with ordinary tile, the extra cost may not be needed. On a lobby floor of large-format porcelain, it usually is.

Substrate and mixing basics
Mortar performance assumes the rest of the system is right. The TCNA Handbook sets substrate tolerances for thin-bed methods, tightening them for large format tile: 1/8” in 10’, with no more than 1/16” variation in 24”.3 It says project specifications must include a specific and separate requirement to bring the substrate into compliance where a thin-bed method is specified and the substrate does not meet the flatness requirement.3 Backer board makers set their own rules for the mortar beneath the board as well as the tile above it, and those are part of the assembly, not optional detail.
On site, the variables are water, mixing and slake time. Mortar mixed too wet loses strength; mortar used past its pot life has already begun to set. Both look fine going down and fail later. Follow the bag, mix in full batches where the job allows it, and do not retemper a batch that has stiffened.
Specifying and submitting
- Name the ANSI standard and any letter designations required, not just a brand.
- Check the membrane's requirement first; it may demand unmodified mortar.
- Match the mortar to the tile size and weight, and to the substrate.
- State the required coverage, and verify it by pulling a tile during installation.
- Keep the bag labels or data sheets with the submittal record.
The TCNA Handbook also notes that where a specification lists more than one material, it must say clearly which is desired, or the contractor may choose any listed option.3 Vague mortar language is how a job ends up with the cheapest compliant bag. For assembling the package, see the submittal checklist.

Sources
- Schluter Systems, “How do I know if the thin-set mortar is modified or unmodified?”. schluter.com/schluter-us/en_US/faq/ditra-ditraxl-thin-set-mortar-modifie
- TEC (H.B. Fuller Construction Products), “Overview of Polymer-Modified Mortars”. tecspecialty.com/product-support/blog/overview-of-polymer-modified-morta
- Tile Council of North America (via CSI Louisville), “tcna-handbook-excerpt”. csilouisville.org/images/downloads/2024_tcna_handbook_shorten_v_ky_.pdf
- The Construction Specifier, “Tile and stone lippage: What is acceptable (and how do you specify it?) - Page 2 of 2 - Construction Specifier”. constructionspecifier.com/tile-and-stone-lippage-what-is-acceptable-and-
General information for the flooring trade. This article was drafted with AI assistance and checked against the sources listed above; the manufacturer's current instructions and the project specification govern any real job. If something here is wrong or out of date, tell us.